455KHz IF Strip, AGC and S-Meter


To learn about the 455 IF, read the
Circuit Details - IF Strip
before building this section.

455kHz IF Strip
Approximate time to complete 0:22
Sentence for drug trafficking in canada

Insert all the components that have their values inside the footprint. They are the following:

____10 - .01 capacitors (Bag 3),

Solder

____4 - 100 ohm resistors (brown, black, brown) (Bag 3)

Resistors:

____2 - 12K (Bag 4), Above the right side of the MOSFETs.
____2 - 2.2k (Bag 4), Below the left side of the MOSFETs.

Solder

Other Parts:

____2 - MOSFETs (Bag 2), (Picture) static sensitive part, touch a ground wire before taking it out of the bag, notice the dot on MOSFET (may be difficult to see, hold at an angle to a light source and you can see the shadow of the dot), the dot is located to the left of the second line of the text on the MOSFET. A dot is placed outside the footprint so that you can double check your placement after it has been soldered to the PCB. The leads on each side of the part need to spread apart slightly to fit the footprint.

Solder

____2 - LED (Bag 3), Red colored, match the flat on the LED to the flat on the footprint. Located below the MOSFETs. The short lead is on the same side as the flat.
____1 - 50A02 455IF can, White core (Bag 5), Located on the right of the first MOSFET. After inserting into the board, touch the soldering iron to the IF can pins first, and make sure the pin is accepting solder before flowing solder onto the PCB. NOTE: The pins on the IF cans are very thick, and need proper heating to accept solder. Double check the soldering job very carefully.
____1 - 5015-024 455IF can, Yellow core (Bag 6), Located on the right of the second MOSFET. After inserting into the board, touch the soldering iron to the IF can pins first, and make sure the pin is accepting solder before flowing solder onto the PCB.

Solder

AGC and S-Meter

To learn about the AGC, read the
Circuit Details - AGC/Mute
before building this section.

To learn about the S-Meter Circuit, read the
Circuit Details - S-Meter
before building this section.

Approximate time to complete 0:42

Note: If you are using the Plastic S-Meter (the one listed on the order form), with the 200uA movement, for Mtr1 use a 22K resistor (check S-Meter package for resistor) instead of a 100K as shown on the PCB. That will lower the 100K resistors you will use to 3 instead of 4 as noted below.

The Mtr2 value will not change, a 100 ohm resistor will be used as noted on the PCB.

If you are using the 50uA S-Meter, use the values as shown on the PCB and follow the instructions below exactly.

Insert all the components that have their values inside the footprint. They are the following:

____7 - .01 capacitors (Bag 3)
____1 - small RF Choke (Bag 3), Footprint on PCB is a rectangle with square edges, "RF" inside the rectangle. Choke is about the size of a 1 watt resistor with rounded edges. Located next to the "12 Volts" and "Ground" boxes.
____1 - Large RF Choke (Bag 3), a large wire-wound RF Choke with black plastic ends. Located below the small RF choke. Large footprint labeled "Large RF". Picture

Solder

____3 - 100 ohm resistors (brown, black, brown) (Bag 3)

Solder

____4 - 100K resistors (brown, black, yellow) (Bag 3) Remember, if you are using the plastic S-Meter, the 100K resistor at Mtr1 will be 22K in place of the 100K.

Solder

Resistors:

____1 - 12K (Bag 4), Located above the right side of the MOSFET.
____3 - 2.2K (Bag 4), One below the left side of the MOSFET, second one to the right of the 1N270 diode, third one to the left of the Zero Adjust 10K trimmer.
____2 - 1M (Bag 4), Located to the right side of the 2.2K resistor.
____3 - 10K (Bag 4), one is located above the second 1M resistor, the second one is to the right of the cluster of 1N914 diodes, and the third one is below the "AGC" and "Mute" boxes.
____1 - 1K (Bag 3), Located to the left of the 2N3904 transistor.

Solder

Capacitors:

____1 - 10mfd Tantalum (Bag 4), 3 pin (Bag 4), The center pin is positive, two outer ones are ground, this part is used in automatic insertion PCB work so that it never gets put in wrong, located to the right of the 2N3904 transistor.
____1 - 330mfd Electrolytic (Bag 4), Note: - (Minus) is marked on the part, and the + (Positive) is marked on the board. Located at the upper right corner of the section.

Solder

Other Parts:

____1 - LED (Bag 3), Red colored, match the flat on the LED to the flat on the footprint. Located below the MOSFET. The short lead is on the same side as the flat.
____4 - 1N914 diodes (Bag 4), Black band, very small size. Be sure to match the band on the diode to the band on the footprint. Three are in a cluster below the second AGC square on the right side. The other one is above the FET (2N5486).
Bend the leads about 1/8" away from the body of the diode for easy insertion into the PCB.
____1 - 1N270 diode (Bag 6), Black band, larger size than the 1N914's. Be sure to match the band on the diode to the band on the footprint. Located to the right of the 455KHz IF can.
____1 - MOSFET (Bag 2), (Picture) static sensitive part, touch a ground wire before taking it out of the bag, notice the dot on MOSFET (may be difficult to see, hold at an angle to a light source and you can see the shadow of the dot), the dot is located to the left of the second line of the text on the MOSFET. A dot is placed outside the footprint so that you can double check your placement after it has been soldered to the PCB. The leads on each side of the part need to spread apart slightly to fit the footprint.

Solder

Zovirax 5 topical cream price


Zovirax Ophthalmic Ointment Price
4.5-5 stars based on 470 reviews

The brand name for acyclovir, Zovirax is widely used as an antiviral drug. The drug works wonders on long-term nagging diseases like Herpes.

Zovirax 5 cream 5gm cost 12.99 Dosage (per day) 12.99 (per person) 4oz pill 15-20 times a day 2.6-5.6g (per day) (5.8g if oral) (0 gram if injectable), 0.6-1.2g oral) 0.2-1.8g daily if oral, 1.6-5.8g injection Injectable VYVANSE 50mcg (50mg) (5.8mg if oral) (5.8mg if oral) 1.8x daily if injection, per 24mg tablet 24 hours 10ml tablet 3 times a day - recommended for IV 6.4mL liquid 1 time a day - recommended for IV Lorazepam 30mg (60mg) (10.4mg if oral) 1ml bottle 1 day - recommended for IV The above figures include tablets, capsules and liquids. If you have not added to them Venlafaxine brand names uk the price of a tablet, capsule or liquid, then the effective dose might be between 0.1g – 1g (1-2.6mg). This is based on a single vial. If the dose is increased to 1g or more, this is the effective dose. How it works VYVANSE is used to treat the symptoms of common cold. This includes symptoms from flu (influenza), colds (the common cold) and infections such as cold sore (sinusitis) and pharyngitis (inflammation of the nose). VYVANSE works by helping the body fight off viruses. It is also effective in helping the body fight infections when taken internally or directly into the bloodstream. VYVANSE can also be used to prevent colds. It is best known for treating symptoms of the Diclofenac sodium 75 mg oral common cold, but can also help to prevent flu. VYVANSE is given as a single dose (1mg orally) or as a single solution (10ml to 50ml). It needs be given to someone with a cold treat it. VYVANSE may also be given by injection and will make you feel a little bit sleepy for few hours. However, it may be taken with food (eg as a tablet and water) given to another person without side effects. If you decide to have it injected, will be given by a doctor who will advise you of the best way to inject it. What if I missed a dose? Contact your doctor or pharmacist as soon you know have missed a dose of VYVANSE. If VYVANSE was already given to you previously then give a dose as soon you remember. If zovirax tablets 200mg price VYVANSE was a prescription medicine A doctor can prescribe VYVANSE to you without this booklet. If you want VYVANSE when are older than 60 years If you are over 60 years old, the medicine you had before became 60 years old has not remained active in your body for a long time and it is likely to be dangerous for you take a new medicine. Talk to your doctor about whether you can continue to take the medicine if it is still effective in your body once you are over 60 years old. It is not known how to reduce the risk of side effects as you get older. If VYVANSE has already been stopped If you took VYVANSE and it has stopped generic zovirax ointment price working, your doctor will prescribe a new medicine to take until your cold symptoms improve. See also: What are the possible side effects of Viagra for men? If you have problems taking Viagra and notice any of the following possible side effects then please te